Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Blog Article
What are your thoughts regarding A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have certified on your own for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will assist you mount a brand-new bathtub in your bathroom if you have already gotten a brand-new bathtub and also don't need to change the plan of your previous water system pipelines.
Your devices and also product list need to comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier provided backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and also inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least when as this will settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, causing the water to penetrate the wall between the bathroom and the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can split rather very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our article on Installing A Bathtub. Thanks so much for taking the time to read through our post. Are you aware of another individual who is involved in How to Install a Bathtub Yourself? Be sure share it. Many thanks for your time. Come back soon.
Book A Service
Report this page